Remote field testing (RFT) is one of the electromagnetic NDT methods most commonly employed in the field of testing and inspection. Other electromagnetic inspection methods include magnetic flux leakage, conventional eddy current, and alternating current field measurement testing.
Remote field testing is associated with eddy current testing and the term remote field eddy current testing is often used when describing remote field testing. However, there are several major differences between eddy current testing and remote field testing.
RFT NDT is primarily used to inspect ferromagnetic tubing since conventional eddy current techniques have difficulty inspecting the full thickness of the tube wall due to the strong skin effect in ferromagnetic materials. For example, using conventional eddy current bobbin probes to inspect a steel pipe 10 mm thick (such as what might be found in heat exchangers) would require frequencies around 30 Hz to achieve adequate I.D. to O.D. penetration through the tube wall. The use of such a low frequency results in a very low sensitivity of flaw detection. The degree of penetration can, in principle, be increased using partial-saturation eddy current probes, magnetically biased probes and pulsed saturation probes. However, because of the large volume of metal present, as well as potential permeability variations within the product, these specialist eddy current probes still have limited inspection capabilities.
The difficulties encountered in the testing of ferromagnetic tubes can be greatly alleviated with the use of the remote field testing method. The RFT NDT method has the advantage of allowing nearly equal sensitivities of detection at both the inner and outer surfaces of a ferromagnetic tube. The method is highly sensitive to variations in wall thickness and tends to be less sensitive to fill-factor changes between the coil and tube.
RFT NDT can be used to inspect any conducting tubular product, but it is generally considered to be less sensitive than conventional eddy current techniques when inspecting non-ferromagnetic materials. Near Field Testing (NFT) technology is a rapid and cost-effective solution intended specifically for fin fan cooler inspection on carbon-steel tubing. This new technology relies on a simple driver-pickup eddy current probe design that provides very simple signal analysis. NFT is specifically suited to the detection of internal corrosion, erosion or pitting in carbon steel tubing.
The NDT probes for near field testing measure lift-off or 'fill factor' and convert it to amplitude-based signals (no phase analysis). Because eddy-current penetration is limited to the inner surface of the tube, NFT probes are not affected by the fin geometry on the outside of the tube.
Comprehensive testing services
Applus+ offers a comprehensive service in NFT NDT and inspection. For heat exchanger tube inspection, Applus+ offers five inspection methods:
Choosing the appropriate inspection method for your equipment depends on your tube material and specific inspection needs. All our NDT technicians are trained to use all techniques, so they can perform complementary inspections, providing the most comprehensive service possible.
The best crews in the business
The key Applus+ differentiator is the high level of training received by our NDT technicians, who work efficiently and report quickly on RTF NDT projects.
The electromagnetic NDT crews at Applus+ are unique in the industry:
As a result, we can typically provide:
Thorough reports, fully explained
Reports are only useful when the customer understands them fully.
Applus+ ensures our customers understand our reports for their electromagnetic NDT projects by:
The Applus+ goal is to provide excellent service and go beyond the industry standard.
NFT and RFT NDT techniques are of particular interest to the petrochemical, power-generation and industrial manufacturing sectors.
Ferromagnetic tubes in heat exchangers, boilers, and air fin coolers are most commonly found in the petrochemical industry. Carbon steel, an inexpensive material, has good mechanical properties and heat-transfer capabilities. However, it is often employed in conditions where if corrosion sets in, it acts very fast. Over the years, with shrinking maintenance budgets and longer intervals between plant shutdowns, the need for reliable inspection of these units has increased. The advent of digital technology has led to several enhancements to the inspection equipment based on RFEC, magnetic flux leakage, and ultrasonic IRIS. Each of these techniques has its own merits and drawbacks.
RFT NDT has several benefits over other electromagnetic NDT techniques:
NFT technology uses two coils — a transmitter and a receiver. Typically, the receiver coil is close to the transmitter coil, taking advantage of the transmitter’s near-field zone – that is, the zone where the magnetic field from the transmitter coil induces strong eddy currents, axially and radially, in the tube wall.
NDT probes for near-field testing operate within the same frequency range as RFT probes.
NFT is specifically suited to detecting corrosion, erosion, and pitting inside carbon steel tubing. NFT is perfect for fin fan cooler inspections on heat exchangers because eddy currents do not pass through the wall of the tube. NFT is also much more sensitive to defects close to structures such as support plates and tube sheets.
Benefits of Near field testing:
Applus+ uses first-party and third-party cookies for analytical purposes and to show you personalized advertising based on a profile drawn up based on your browsing habits (eg. visited websites). You can accept all cookies by pressing the "Accept" button or configure or reject their use. Consult our Cookies Policy for more information.
They allow the operation of the website, loading media content and its security. See the cookies we store in our Cookies Policy.
They allow us to know how you interact with the website, the number of visits in the different sections and to create statistics to improve our business practices. See the cookies we store in our Cookies Policy.